高压去毛刺清洗机工艺采用在加压室内燃烧甲烷气体的方法，通过氧化反应从加工过的零件上去除毛刺、毛边或隐藏的污染物。那么您知道高压去毛刺清洗机的日常维护是怎样的吗？

The high-pressure deburring and cleaning machine process uses the method of burning methane gas in the pressurized chamber to remove burrs, burrs or hidden pollutants from the processed parts through oxidation reaction. Do you know how the daily maintenance of the high-pressure deburring cleaning machine is?

1.保持设备放置通风、干燥、洁净场地，有利于设备的长期高效运转和使用寿命；

1. Keep the equipment in a ventilated, dry and clean place, which is conducive to the long-term efficient operation and service life of the equipment;

2.使用前务必一定请仔细阅读说明书；

2. Please read the instructions carefully before use;

3.电源：使用合符设备规格的电源及电源线，用户方需装设专用于清洗机的空气开关；并定期测试电源；

3. Power supply: use the power supply and power cord that meet the equipment specifications, and the user needs to install the air switch specially used for the cleaning machine; And regularly test the power supply;

4.电气控制箱及相关电气组件及设备通风口等注意防水，并远离水蒸汽、腐蚀性气体、粉尘等；定期用压缩空气清理附着的灰尘；

4. The electrical control box and relevant electrical components and equipment vents shall be waterproof and kept away from water vapor, corrosive gas and dust; Clean the attached dust with compressed air regularly;

5.设备长期不用时，请放出洗净液，干燥内槽及表面后，做好防尘和防潮工作，并拔下电源插头

5. When the equipment is not used for a long time, please release the cleaning liquid, dry the inner tank and surface, do a good job in dust and moisture prevention, and unplug the power plug

6.洗净槽中无液或液位不足都会对设备造成不可逆损伤；

6. No liquid or insufficient liquid level in the washing tank will cause irreversible damage to the equipment;

7.要清洗的工件应放在洗篮中清洗，禁止直接放在清洗槽内；

7. The workpiece to be cleaned should be placed in the washing basket for cleaning, and it is prohibited to put it directly in the washing tank;

8.定期测试设备的绝缘性能；定期检查易老化电气组件；定期检查传动部位螺栓，紧固电柜内线头固定螺栓，及各部分紧固螺栓等；

8. Regularly test the insulation performance of the equipment; Regularly check the aging electrical components; Regularly check the bolts of the transmission parts, fasten the fixing bolts of the wire head in the electric cabinet and the fastening bolts of each part;

9.山东超声波清洗机设备带有过滤装置的，应定期更换过滤芯；清洗机配件带有传动机构的，应定期加注机油、黄油等润滑剂，定期更换减速机齿轮油；

9. If Shandong ultrasonic cleaner equipment is equipped with filter device, the filter element shall be replaced regularly; If the parts of the cleaning machine are equipped with a transmission mechanism, oil, butter and other lubricants shall be regularly filled, and the gear oil of the reducer shall be regularly replaced;

10.长时工作的清洗机，在停机前，风机需再工作3～6分钟后关机，以保证电源内部热量散出；

10. For the long-time cleaning machine, before shutdown, the fan shall be shut down after 3-6 minutes of operation to ensure that the heat inside the power supply is released;

11.清洗液应及时沉淀、过滤或更换；定期清理储油箱被污染的清洗液；定期让油泵运转一次，每次至少在10min以上。

11. The cleaning solution shall be precipitated, filtered or replaced in time; Regularly clean the contaminated cleaning liquid in the oil storage tank; The oil pump shall be operated regularly for at least 10min each time.

注意：将每个需要去毛刺或毛边的零件松散地放在专用篮内（非关键部件），或固定在一块板子内，然后放入燃烧室进行加工。期间要使用正确的操作方式才行，更多相关内容就来我们网站www.jnthcsb.com咨询看看吧。

Note: each part requiring deburring or burring shall be loosely placed in a special basket (non key part) or fixed in a plate, and then placed into the combustion chamber for processing. During this period, you should use the correct operation mode. For more information, please visit our website www.jnthcsb.com.