多槽超声波清洗机适用于油漆、陶瓷和软质材料。可用于电子元器件、电镀、五金、手表、表带、工具、光学镜片、宝石、喷丝板、眼镜框、半导体硅片、旋转滤嘴及玻璃制品、手机配件、汽车维修等。但是用多槽超声波清洗机清洗不规则喷丝板注意以下五点。

Multi groove ultrasonic cleaning machine is suitable for paint, ceramics and soft materials. It can be used in electronic components, electroplating, hardware, watch, watch strap, tool, optical lens, gem, spinneret, eyeglass frame, semiconductor silicon chip, rotary filter and glass products, mobile phone accessories, automobile maintenance, etc. However, when cleaning the irregular spinneret with multi slot ultrasonic cleaning machine, pay attention to the following five points.

多槽超声波清洗机机

Multi slot ultrasonic cleaning machine

1、多槽超声波清洗机清洗时间

1. Cleaning time of multi tank ultrasonic cleaning machine

清洗时间的设定因喷丝板和产品的不同而不同。设定正确的时间，可以节省时间，达到好的清洁效果(通常设定的时间为10-20分钟)。

The setting of cleaning time varies with spinneret and product. Setting the right time can save time and achieve good cleaning effect (usually the setting time is 10-20 minutes).

如果时间太短，工件就不能清洗。如果时间过长，水洗后的样品表面会出现空化斑点，影响表面光洁度。

If the time is too short, the workpiece cannot be cleaned. If the time is too long, cavitation spots will appear on the surface of the sample after washing, which will affect the surface finish.

2、多槽超声波清洗机清洗温度因素

2. Cleaning temperature factors of multi tank ultrasonic cleaning machine

由于每个不规则喷丝板的物理特性不同，清洗时需要选择不同的清洗温度。例如，油脂一般超过50摄氏度，但对于铝件，一般选择40摄氏度左右比较合适。温度太高了。氧化斑点形成，但在有毛刺的情况下，一般建议选择小于15摄氏度的。用多槽超声波清洗机清洗不规则喷丝板注意以下五点。

Due to the different physical characteristics of each irregular spinneret, different cleaning temperature should be selected. For example, the grease is generally over 50 ℃, but for aluminum parts, it is more appropriate to choose about 40 ℃. The temperature is too high. Oxidation spots are formed, but in the case of burr, it is generally recommended to choose the one less than 15 ℃. Clean irregular spinneret with multi slot ultrasonic cleaning machine, pay attention to the following five points.

3、多槽超声波清洗机频率

3. Multi slot ultrasonic cleaning machine frequency

多槽超声波清洗机超声波频率一般在25KHZ到130KHZ之间。使用水或水超声波清洗喷丝板清洗剂时由空化引起的物理清洗功率对低频明显有利，一般在15-30kHz左右。清洁有小缝隙、狭缝和深孔的喷丝板。建议使用几百kHz的高频(通常为40kHz或更多)。请使用400kHz来保养手表喷丝板。使用宽带调频清洗时，效果会更好。

The ultrasonic frequency of multi slot ultrasonic cleaning machine is generally between 25kHz and 130KHz. When using water or water ultrasonic to clean spinneret cleaner, the physical cleaning power caused by cavitation is obviously beneficial to the low frequency, which is generally about 15-30KHZ. Clean spinneret with small gaps, slits and deep holes. A high frequency of several hundred kHz (usually 40 kHz or more) is recommended. Please use 400kHz to maintain the watch spinneret. When using broadband FM cleaning, the effect will be better.

4、超声波清洁力

4. Ultrasonic cleaning power

标准多槽超声波清洗机的功率范围从100W到1500W。大功率产品主要用于清洗五金、机械等行业，或用于重污染的常见喷丝板。

The power range of standard multi slot ultrasonic cleaning machine is from 100W to 1500W. High power products are mainly used for cleaning hardware, machinery and other industries, or for heavy pollution common spinneret.

5、超声波清洗方案

5. Ultrasonic cleaning solution

选择正确的清洁溶液可以帮助你清洁不规则喷丝板。传统的清洗溶液(介质)包括水基溶液和有机溶液，如酒精和汽油。目前的多槽超声波清洗机超声波清洗剂是各种清洗剂、润湿剂和其他可回收组分的混合物。

Choosing the right cleaning solution can help you clean the irregular spinneret. Traditional cleaning solutions (media) include water-based solutions and organic solutions, such as alcohol and gasoline. At present, the ultrasonic cleaning agent of multi tank ultrasonic cleaning machine is a mixture of various cleaning agents, wetting agents and other recyclable components.

可以选择一些的针对性多槽超声波清洗机清洗剂，达到适当的清洗效果，防止喷丝板和(清洗液)发生反应。

Some excellent targeted multi slot ultrasonic cleaning agent can be selected to achieve proper cleaning effect and prevent the spinneret from reacting with (cleaning fluid).