多槽手动超声波清洗机的使用方法相对简单，但为了确保最佳的清洗效果和安全性，需要遵循一定的操作步骤。以下是详细的使用方法：

The usage method of the multi slot manual ultrasonic cleaning machine is relatively simple, but in order to ensure the best cleaning effect and safety, certain operating steps need to be followed. The following is a detailed usage method:

一、准备工作

1、 Preparation work

环境准备：确保清洗环境通风良好，干燥无尘，以避免灰尘和湿气对清洗效果和机器造成不良影响。

Environmental preparation: Ensure that the cleaning environment is well ventilated, dry and dust-free to avoid adverse effects of dust and moisture on the cleaning effect and machine.

检查设备：轻微摇晃机器，听机箱内有无响声，确认零件有否松脱。确认清洗机的各个部件完好无损，特别是超声波发射棒和清洗槽。

Check equipment: Gently shake the machine, listen for any noise inside the chassis, and confirm if any parts are loose. Confirm that all components of the cleaning machine are intact and undamaged, especially the ultrasonic emitter and cleaning tank.

放置设备：将清洗机放置在平稳、水平的地面上，确保其在工作过程中不会晃动或倾倒。

Placement of equipment: Place the cleaning machine on a stable and level surface, ensuring that it does not shake or tilt during operation.

二、填充清洗液

2、 Fill with cleaning solution

选择合适的清洗槽：根据清洗物品的大小和数量，选择合适的清洗槽位。

Choose the appropriate cleaning tank: Select the appropriate cleaning tank position based on the size and quantity of the cleaning items.

添加清洗液：向清洗槽中加入适量的清洗液。一般来说，可以使用清水或中性清洁剂作为清洗液。如果需要加热清洗液，应确保液位不低于槽深的2/3，以避免加热过程中液位下降过多。

Add cleaning solution: Add an appropriate amount of cleaning solution to the cleaning tank. Generally speaking, water or neutral cleaning agents can be used as cleaning solutions. If it is necessary to heat the cleaning solution, it should be ensured that the liquid level is not lower than 2/3 of the tank depth to avoid excessive liquid level drop during the heating process.

调整液位：确保清洗液的液位高出发射棒约10cm，以保证超声波能够充分作用于清洗液中的物品。

Adjust the liquid level: Ensure that the liquid level of the cleaning solution is about 10cm higher than the emitting rod to ensure that the ultrasonic waves can fully act on the items in the cleaning solution.

三、启动清洗机

3、 Start the cleaning machine

启动发射棒：在加入清洗液后，先启动发射棒，并调节到适当位置。待槽位内液位上升至发射棒一半高度时，方可启动清洗程序。

Start the firing rod: After adding the cleaning solution, start the firing rod first and adjust it to the appropriate position. The cleaning program can only be started when the liquid level in the slot rises to half the height of the launch rod.

设置清洗时间和温度：根据清洗物品的需求和清洗液的特性，设置合适的清洗时间和温度。一般来说，清洗时间在5~15分钟内可达到理想的清洗效果。如果需要加热清洗液，应调节至适当的温度（如40-60度），以提高清洗效果。

Set cleaning time and temperature: Based on the needs of the cleaning items and the characteristics of the cleaning solution, set the appropriate cleaning time and temperature. Generally speaking, the ideal cleaning effect can be achieved within 5-15 minutes of cleaning. If it is necessary to heat the cleaning solution, it should be adjusted to an appropriate temperature (such as 40-60 degrees) to improve the cleaning effect.

启动清洗程序：按下清洗机上的启动按钮，开始清洗程序。此时，超声波波能会产生并作用于清洗液中的物品。

Start cleaning program: Press the start button on the cleaning machine to start the cleaning program. At this point, ultrasonic waves can generate and act on the items in the cleaning solution.

四、清洗过程与监控

4、 Cleaning process and monitoring

监控清洗过程：在清洗过程中，应密切关注清洗机的运行状态和清洗效果。如果发现异常情况（如声音异常、清洗液溅出等），应立即停机检查并排除故障。

Monitoring the cleaning process: During the cleaning process, close attention should be paid to the operating status and cleaning effect of the cleaning machine. If any abnormal situation is found (such as abnormal sound, splashing of cleaning solution, etc.), the machine should be stopped immediately for inspection and troubleshooting.

避免离开：在清洗过程中，不要离开清洗机太远或长时间无人看管，以防止发生意外情况。

Avoid leaving: During the cleaning process, do not leave the cleaning machine too far away or unattended for a long time to prevent unexpected situations.

五、清洗后处理

5、 Post cleaning treatment

取出清洗物品：待清洗完成后，及时将清洗物品从清洗槽中取出。注意避免烫伤或划伤手部。

Remove cleaning items: After cleaning is completed, promptly remove the cleaning items from the cleaning tank. Be careful not to burn or scratch your hands.

清洗槽清洗：用清水将清洗槽中的清洗剂冲掉，并用干净的布擦拭干净。确保清洗槽内无残留物或清洗剂。

Cleaning tank cleaning: Rinse off the cleaning agent in the cleaning tank with clean water and wipe it clean with a clean cloth. Ensure that there are no residues or cleaning agents in the cleaning tank.

机器维护：清洗完成后，将清洗机放在干燥通风的地方，以便其自然晾干。定期检查清洗机的各个部件是否完好无损，如有损坏应及时更换或维修。

Machine maintenance: After cleaning, place the cleaning machine in a dry and ventilated place for it to air dry naturally. Regularly check whether the various components of the cleaning machine are intact and undamaged. If there is any damage, they should be replaced or repaired in a timely manner.

六、注意事项

6、 Precautions

阅读说明书：在使用前请仔细阅读清洗机的说明书，了解其基本结构、操作方法和安全注意事项。

Read the instruction manual: Before use, please carefully read the manual of the cleaning machine to understand its basic structure, operating methods, and safety precautions.

正确连接电源：请确保所供电源有可靠接地线，以避免触电危险。

Correctly connect the power supply: Please ensure that the supplied power supply has a reliable grounding wire to avoid the risk of electric shock.

避免不当使用：请勿将清洗机用于不适当的物品或环境中，以免造成人身伤害或财产损失。

Avoid improper use: Do not use the cleaning machine in inappropriate items or environments to avoid personal injury or property damage.

注意安全：在操作过程中应注意安全，避免手部或其他身体部位接触到高速旋转的部件或高温的清洗液。

Attention to safety: During operation, attention should be paid to safety and avoid contact between hands or other body parts and high-speed rotating components or high-temperature cleaning solutions.

通过遵循以上步骤和注意事项，您可以有效地使用多槽手动超声波清洗机进行清洗工作，并确保其长期稳定运行。

By following the above steps and precautions, you can effectively use a multi slot manual ultrasonic cleaning machine for cleaning work and ensure its long-term stable operation.

本文由多槽手动超声波清洗机友情奉献.更多有关的知识请点击:http://www.jnthcsb.com 真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

This article is a friendly contribution from a multi slot manual ultrasonic cleaning machine. For more related knowledge, please click: http://www.jnthcsb.com Sincere attitude. We provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Please stay tuned