随着超声波清洗机设备的应用范围越来越广泛，而通过式清洗机所采用的通过式清洗技术采用频率28KHz的超声波进行清洗，由喷淋系统、喷嘴旋转装置、磷化系统、自动温控加热系统、风切吹水系统等组成。对于某些特定的清洗对象，还配有热空气烘干、专用清洗架及清洗液的过滤循环系统。

As the application range of ultrasonic cleaning machine equipment becomes wider and wider, the through cleaning technology adopted by the through cleaning machine uses 28kHz ultrasonic wave for cleaning, which is composed of spray system, nozzle rotating device, phosphating system, automatic temperature control heating system, air cutting and water blowing system, etc. For some specific cleaning objects, it is also equipped with hot air drying, special cleaning rack and cleaning liquid filtration and circulation system.

通过式清洗机工作时，将料框置于输送带上，清洗工件装于相对应的料框中，零件不得重叠，节拍为2-3min/筐；料筐依次通过清洗室、漂洗室、吹干、烘干室，完成全过程后自动输出清洗洁净的零件，如有水珠需进行人工补吹，将吹干后的零件放入防尘周转箱。

When the through type cleaning machine works, place the material frame on the conveyor belt, and install the cleaned workpiece in the corresponding material frame. The parts shall not overlap, and the beat is 2-3min/basket; The material basket passes through the cleaning room, rinsing room, drying room and drying room in turn. After the whole process is completed, the cleaned parts will be automatically output. If there are water drops, manual supplementary blowing is required. The dried parts will be put into the dust-proof turnover box.

相比传统的清洗设备，通过式清洗机的主要特点是不仅能有效的避免高光洁度物体的表面损伤；而且可除去附着在表面的亚微米大小的颗粒；甚对浸入液体中，面向换能器的一面也能被洗净，所以要进行两面清洗。

Compared with the traditional cleaning equipment, the main characteristics of the through type cleaning machine are that it can not only effectively avoid the surface damage of high finish objects; And can remove submicron sized particles attached to the surface; Even the side facing the transducer when immersed in liquid can be cleaned, so both sides should be cleaned.

操作通过式清洗机的时候，注意要将被清洁的零件要规整地放在运送带上，不许压在滚轮上；而且在运送带上，被清洁的零件不能堆得过多，避免影响清洁作用，每个零件都能清洁到。

When operating the through type cleaning machine, pay attention to placing the cleaned parts on the conveyor belt in an orderly manner, and do not press on the rollers; Moreover, on the conveyor belt, the cleaned parts cannot be stacked too much to avoid affecting the cleaning effect, and each part can be cleaned.

通过式清洗机作业后，被清洁的零件不能停放在运送带上，按中止按钮，使全机中止运转。清洁液应定时添加水和必定份额的金属清洁剂以弥补耗费，使液面保持在必定高度，若是清洁作用达不到规则的技术需求时，应悉数替换清洁液。

After the operation of the through type cleaning machine, the cleaned parts cannot be parked on the conveyor belt. Press the stop button to stop the whole machine. Water and a certain proportion of metal cleaner shall be added to the cleaning liquid regularly to make up for the consumption and keep the liquid level at a certain height. If the cleaning effect cannot meet the regular technical requirements, all the cleaning liquid shall be replaced.

通过式清洗机操作工艺的具体使用事项就讲解到这里了，以上内容您可以作为有关参考信息使用，当然要注意每日的检查和定期的维修保养事项，更多注意就来我们网站www.jnthcsb.com咨询吧！

Here are the specific use matters of the operation process of the pass through washer. You can use the above contents as relevant reference information. Of course, you should pay attention to daily inspection and regular maintenance. For more attention, please come to our website www.jnthcsb.com!