欢迎访问济南科尔超声波设备有限公司网站!

专注生产工业用超声波清洗机

让工业清洗无难事

电话

业务咨询电话:

18663767799

你所在位置: 首页-新闻动态-常见问题轻松使用CNC高压清洗机的八大步
常见问题

轻松使用CNC高压清洗机的八大步

作者:admin来源:http://www.jnthcsb.com/时间:2022-12-22

CNC高压清洗机的类型和压力大小尽管有所不同,可是它的基本构造、大部构成、作业原理等大致一样,只不过是用处各有侧重罢了。下面小编为大家总结了CNC高压清洗机使用的八大步。
Although the brand type and pressure size of CNC high-pressure cleaning machine are different, its basic structure, most of its composition, operating principle, etc. are roughly the same, but each has its own emphasis on its use. The following section summarizes the eight steps of using CNC high-pressure cleaning machine.
1:CNC高压清洗机在开机前应作的预备:主要是要做好相关查看,主要的是润滑油要在规定的油位,通常应是在观察窗上下两刻线之间的方位。查看各个联系方位是不是严密,使构造衔接处在杰出状况。
1: Preparations for CNC high-pressure washer before starting up: it is mainly to make relevant checks, and the main thing is that the lubricating oil should be at the specified oil level, usually at the position between the upper and lower reticles of the observation window. Check whether the contact directions are tight, so that the structural connection is in an outstanding condition.
2:把高压泵的进水管接口与进水管相衔接,而且固定好,使它不漏气不漏水。然后把另一端和自来水水管衔接或刺进供水池供水桶。并查看杂质过滤器是不是无缺。
2: Connect the water inlet pipe interface of the high-pressure pump with the water inlet pipe, and fix it to make it air tight and water tight. Then connect the other end with the tap water pipe or pierce it into the water supply tank for water supply. Check whether the impurity filter is intact.
3:CNC高压清洗机把高压泵的出水口与出水高压胶管相衔接,胶管另一端则与高压喷枪的枪杆相衔接。
3: The CNC high-pressure washer connects the water outlet of the high-pressure pump with the outlet high-pressure hose, and the other end of the hose is connected with the barrel of the high-pressure spray gun.
4:把CNC高压清洗机与供电线路相衔接。衔接时要查看电源电压是不是匹配,要辨明应该用220V的仍是应该用380V的电压。在准确衔接电源后,就能够启动设备的开关了。抠动高压喷枪的操控组织扳机,等高压泵内的空气排完后,高压水射流就能够喷出了。
4: Connect the CNC high-pressure washer with the power supply line. During connection, check whether the power supply voltage is matched, and distinguish whether 220V or 380V should be used. After the power supply is correctly connected, the switch of the equipment can be started. Pull the control and organization trigger of the high-pressure spray gun, and after the air in the high-pressure pump is exhausted, the high-pressure water jet can be ejected.
CNC高压清洗机
5:易损坏物体外表,假如CNC高压清洗机太远,清洁效果会下降。要总结和把握操作的经历。假如清洁间歇时刻超过十分钟时,要关掉高压清洁设备的电源开关,翻开高压喷枪阀,进行卸压,这么有利于维护高压泵的零部件,使之延伸运用寿命。
5: It is easy to damage the appearance of objects. If the CNC high-pressure cleaner is too far away, the cleaning effect will decline. Summarize and grasp the experience of operation. If the cleaning interval exceeds ten minutes, turn off the power switch of the high-pressure cleaning equipment, turn on the high-pressure spray gun valve and relieve the pressure, which is conducive to maintaining the parts of the high-pressure pump and extending its service life.
6:在履行高压清洁使命时,要用高压泵的额外压力作业,一般不要用很高压力进行清洁,CNC高压清洗机若非常有必要用很高压力,也要操控在30分钟以内,及时康复到额外压力作业。
6: When performing the high-pressure cleaning mission, the extra pressure operation of the high-pressure pump should be used, and generally do not use very high pressure for cleaning. If it is very necessary to use very high pressure, the CNC high-pressure washer should also be controlled within 30 minutes to recover to the extra pressure operation in time.
7:完结高压清洁使命后,要及时关机,要先关闭高压清洁设备的电源开关,然后在把电源插头从电源插座上取下。
7: After finishing the high-voltage cleaning mission, shut down the machine in time. Turn off the power switch of the high-voltage cleaning equipment first, and then remove the power plug from the power socket.
8:当要搬运场所履行新的清洁使命时,CNC高压清洗机要运用快换接头拔下高压泵上的出水高压胶管,这么才便利对CNC高压清洗机进行搬运。总之,在操作运用傍边,要特别注重CNC高压清洗机的操作,要把安全出产放在头等主要的方位,这么才干充分发挥高压清洁设备的效果。
8: When it is necessary to carry out a new cleaning mission in the handling place, the CNC high-pressure washer should use the quick change connector to pull off the water outlet high-pressure hose on the high-pressure pump, so as to facilitate the handling of the CNC high-pressure washer. In a word, in the process of operation and application, special attention should be paid to the operation of CNC high-pressure cleaning machine, and safety production should be put in the first place, so as to give full play to the effect of high-pressure cleaning equipment.
关于轻松使用CNC高压清洗机得的八大步的相关内容就到这里了,您对此有什么想法或者需求就来我们网站www.jnthcsb.com咨询吧!
This is all about the eight steps of using the CNC high-pressure washer easily. If you have any ideas or needs, please come to our website www.jnthcsb.com for consultation!