一般来说新购买的多槽手动超声波清洗机在厂家出厂前就已经将超声波的频率与功率之间进行了好的匹配了，用户只需要 调整超声波发生器上的功率电位器或者是功率调整按钮即可，根据被清洗的产品来调整超声波功率就可以了。

Generally speaking, the newly purchased multi slot manual ultrasonic cleaner has well matched the ultrasonic frequency and power before leaving the factory. The user only needs to adjust the power potentiometer or power adjustment button on the ultrasonic generator, and adjust the ultrasonic power according to the product to be cleaned.

如果是超声波的功率对产品表面没有任何损伤就可以将功率调整到大，如果功率对产品有一定的损伤那就可以考虑将超声 波功率调整到60%-80%之间然后观察清洗后产品的损伤情况；

If the ultrasonic power has no damage to the product surface, the power can be adjusted to high. If the power has certain damage to the product, the ultrasonic power can be adjusted to 60% - 80%, and then observe the damage of the product after cleaning;

不是功率越大，对清洗效果越好，而是正确合理的选择超声波功率超声波清洗器超声清洗效果不一定与(功率×清洗时间) 成正比，有时用小功率，花费很长时间也没有清除污垢。

It is not that the higher the power is, the better the cleaning effect will be, but the correct and reasonable selection of ultrasonic power ultrasonic cleaner ultrasonic cleaning effect is not necessarily the same as (power × Cleaning time) is proportional, sometimes with small power, it takes a long time to remove dirt.

而如果功率达到一定数值，有时很快便将污垢去除。若选择功率太大，空化强度将大大增加，清洗效果是提高了，但这时 使较精密的零件也产生蚀点，得不偿失。

If the power reaches a certain value, sometimes the dirt will be removed quickly. If the power is too large, the cavitation strength will be greatly increased, and the cleaning effect will be improved, but at this time, the more precise parts will also have corrosion spots, which is not worth the loss.

使用一定年限的多槽手动超声波清洗机如果用上述方法不能满足就可以考虑通过调整超声波发生器内部的磁芯来进行超声 波功率与频率的匹配了，匹配方法：

If the multi slot manual ultrasonic cleaner with a certain service life cannot meet the requirements of the above methods, it can be considered to match the ultrasonic power and frequency by adjusting the magnetic core inside the ultrasonic generator. The matching method is as follows:

将电感固定螺丝松开，取出E型磁芯中间所有垫片，接上负载开机，功率调至大，慢慢提起电感磁芯，观察电流变化，将磁 芯固定在匹配位置（在不改变磁芯之间高度之外的任何条件，此时电流大点为匹配位置。如果磁芯上提时明显感觉两磁芯之间 有很大的吸力则需改变频率，电流过大也需改变频率）。

Loosen the fixing screws of the inductance, take out all the gaskets in the middle of the E-type magnetic core, connect the load and start the machine, adjust the power to high, slowly lift the inductance magnetic core, and observe the current change, Fix the magnetic core at the matching position (without changing any condition other than the height between the magnetic cores, the matching position is the point where the current is high. If the magnetic core is obviously lifted, it is necessary to change the frequency if there is a great suction between the two magnetic cores, and if the current is too high, it is also necessary to change the frequency).

然后通过比较超声效果，声音来确定一佳频率，根据客户要求（允许范围内）调节电流大小（变压器档位可解决），调试 机器后观察散热片温度上升平稳且到一定温度不再升高为好。

Then determine a good frequency by comparing the ultrasonic effect and sound. Adjust the current according to the customer's requirements (within the allowable range) (the transformer gear can be solved). After debugging the machine, observe that the temperature of the heat sink rises steadily and will not rise again when it reaches a certain temperature.

通过以上的介绍相信大家对于多槽手动超声波清洗机功率调整到多大才合适这个问题应该了解的差不多了吧，如果还需要 了解更多多槽手动超声波清洗机的一些问题请关注我们网站www.jnthcsb.com咨询更多事项！

Through the above introduction, we believe that you should have a good understanding of the problem of how large the power of the multi tank manual ultrasonic cleaner is to be adjusted. If you still need to know more about some problems of the multi tank manual ultrasonic cleaner, please follow our website www.jnthcsb.com for more information!