全自动超声波清洗机的零部件还是挺多的，所以在清洗的时候需要多加注意，那么全自动超声波清洗机盲孔的清洗要注意什么呢？只有多了解才能正确的操作！

　　Automatic ultrasonic cleaning machine parts or a lot of, so in the cleaning time need to pay more attention to, then automatic ultrasonic cleaning machine blind hole cleaning to pay attention to what? Only more understanding can correct operation!

　　在设计全自动超声波清洗机时，可以在罐体上加一个压缩空气喷嘴。外部工厂气源，在清洗盲孔零件时，将工件慢慢放入，尽可能让水流入孔内。零件放置后，利用压缩空气使水产生大量水柱冲击工件。为了使堵塞在孔口中的气泡爆裂，达到更好的对盲孔部位的超声波清洗效果。

　　In the design of automatic ultrasonic cleaning machine, a compressed air nozzle can be added to the tank body. External factory air source, when cleaning the blind hole parts, slowly put the workpiece into the hole, as much as possible to let the water flow into the hole. After the parts are placed, compressed air is used to generate a large number of water columns to impact the workpiece. In order to make the bubbles blocked in the orifice burst, to achieve a better ultrasonic cleaning effect on the blind hole.

　　使用中高频结合的超声波清洗机。利用高频超声波，原理是高频振荡，使堵塞在盲孔中的气体超声波清洗机的气泡破裂，铁屑被一扫而空。

　　The use of high frequency combined with ultrasonic cleaning machine. The use of high frequency ultrasonic, the principle is high frequency oscillation, so that blocked in the blind hole in the gas ultrasonic cleaning machine bubble burst, iron filings were swept away.

　　一般情况下，全自动超声波清洗机使用时的频率在很大程度上决定了超声波清洗机的清洗效果。超声波空化阈值与超声波清洗机的频率密切相关，频率越高，气蚀阀越高。也就是说：频率越低越容易产生空化，而在频率低的情况下，液体被压缩变薄的时间间隔更长，这样气泡在解体前就可以长到更大的尺寸.因此，我们可以通过增加空化强度来提高清洗效率。

　　In general, the frequency of automatic ultrasonic cleaning machine largely determines the cleaning effect of ultrasonic cleaning machine. Ultrasonic cavitation threshold is closely related to the frequency of ultrasonic cleaning machine, the higher the frequency, the higher the cavitation valve. That is: cavitation is more likely to occur at lower frequencies, and at lower frequencies, the liquid is compressed and thinned at longer intervals, allowing bubbles to grow to larger sizes before they disintegrate. Therefore, we can increase the cleaning efficiency by increasing the cavitation intensity.

　　盲孔太小，水压无法使堵在盲孔中的气泡爆裂，超声波的传播是以水为介质，即超声波清洗机说只要水能到达的地方，超声波就会存在，从而实现清洗。但少量未渗入清洗剂的盲孔无法清洗干净。

　　The blind hole is too small, the water pressure can not make the bubble blocked in the blind hole burst, the transmission of ultrasonic is water as the medium, that is, ultrasonic cleaning machine said that as long as water can reach the place, ultrasonic will exist, so as to achieve cleaning. However, a small number of blind holes that have not infiltrated into the cleaning agent cannot be cleaned.

　　全自动超声波清洗机盲孔的清洗要注意什么呢？以上的讲解内容便是问题的详解了，如果您还有清洗机什么方面的清洗事项不懂的，那就来我们网站www.jnthcsb.com咨询吧！

　　What should we pay attention to when cleaning the blind hole of automatic ultrasonic cleaning machine? The above explanation is a detailed explanation of the problem, if you have a cleaning machine what aspects of cleaning matters do not understand, then come to our website www.jnthcsb.com consultation!