欢迎访问济南科尔超声波设备有限公司网站!

专注生产工业用超声波清洗机

让工业清洗无难事

电话

业务咨询电话:

18663767799

你所在位置: 首页-新闻动态-新闻资讯超声波清洗机的各项操作说明
新闻资讯

超声波清洗机的各项操作说明

作者:admin来源:http://www.jnthcsb.com/时间:2022-05-20

很多朋友可能买了超声波清洗机之后并不知道怎么去操作使用,那接下来就让小编给大家介绍一下超声波清洗机正确操作步骤吧。
Many friends may not know how to operate the ultrasonic cleaning machine after buying it. Next, let Xiaobian introduce you to the correct operation steps of the ultrasonic cleaning machine.
安装超声波清洗机
Installation of ultrasonic cleaning machine
清洗机电控柜与主机之间的温控传感器信号线、超声波驱动线、加热器控制线等线路请参考超声波清洗机安装手册,并接好相应的电源。对应的机器,安装好清洗机的供水管,排水管和溢流排水管松手。
Please refer to the installation manual of ultrasonic cleaning machine for the temperature control sensor signal line, ultrasonic drive line, heater control line and other lines between the cleaning electromechanical control cabinet and the host, and connect the corresponding power supply. For the corresponding machine, install the water supply pipe, drainage pipe and overflow drainage pipe of the cleaning machine and let go.
加溶质清洗
Solute cleaning
在清洗池中加入适量的清水。液位的高度取决于要清洗的部件。一般不超过清洗池的四分之三。当然,超声波清洗机的内壁也标明了清洗机的很高水位。只需加水或其他溶剂。说到质量,要注意超声波清洗机内壁以上的很高水位。
Add an appropriate amount of clean water to the cleaning tank. The height of the liquid level depends on the components to be cleaned. Generally not more than three quarters of the cleaning tank. Of course, the inner wall of the ultrasonic cleaning machine also indicates the high water level of the cleaning machine. Just add water or other solvents. When it comes to quality, pay attention to the high water level above the inner wall of the ultrasonic cleaning machine.
在超声波清洗机中加入清洗剂
Add cleaning agent to ultrasonic cleaning machine
如果要清洗的物品需要用清洗剂清洗,在加入清洗物品的溶质后,再将清洗剂加入清洗槽中。缓慢搅拌溶质使其充分溶解(同时打开超声波清洗机的开关,启动机器搅拌溶剂,清洗代理人)。
If the articles to be cleaned need to be cleaned with cleaning agent, add the cleaning agent into the cleaning tank after adding the solute of the cleaned articles. Slowly stir the solute to fully dissolve it (at the same time, turn on the switch of the ultrasonic cleaning machine, start the machine to stir the solvent and clean the agent).
超声波清洗设备
超声波清洗机预处理
Pretreatment of ultrasonic cleaning machine
清洗前请用竹刀将零件表面的污垢清理干净(如果烟尘较多,曲线图中筒件变化时会出现很多很容易去除的厚泥盖)进行简单清洗,以延长清洗液的使用寿命。超声波可用于精密清洗,但其处理污泥的能力较弱,因此在预处理过程中,应尽可能去除黄泥和泥状污垢。
Before cleaning, please clean the dirt on the surface of the parts with a bamboo knife (if there is more smoke, there will be many thick mud covers that can be easily removed when the cylinder parts in the curve change) for simple cleaning, so as to prolong the service life of the cleaning solution. Ultrasonic can be used for precision cleaning, but its ability to treat sludge is weak. Therefore, yellow mud and muddy dirt should be removed as much as possible in the pretreatment process.
放入需要清洗的物品
Put in items to be cleaned
将要清洗的物体放入清洗机的清洗蓝中,轻轻放入超声波清洗机的清洗槽中。一次放置的物体较多时,尽量使它们均匀分布在清洁蓝中,避免重叠。
Put the object to be cleaned into the cleaning blue of the cleaning machine and gently put it into the cleaning tank of the ultrasonic cleaning machine. When there are many objects placed at one time, try to make them evenly distributed in the clean blue to avoid overlap.
启动超声波清洗机
Start the ultrasonic cleaning machine
超声波清洗机使用非常方便,直接按机器的开关机键即可。如果是功率可调的机器,开机后可以选择自己需要的对应机器频率。同时,在一些超声波清洗机的显示屏上带有数显查看相应的频率和其他数据。
The ultrasonic cleaning machine is very convenient to use. Just press the on / off key of the machine. If it is a machine with adjustable power, you can select the corresponding machine frequency you need after starting up. At the same time, there is a digital display on the display screen of some ultrasonic cleaning machines to view the corresponding frequency and other data.
超声波清洗机停止
Stop of ultrasonic cleaning machine
如果在超声波清洗设备清洗过程中要停止清洗,应先将功率调到很小,然后按下停止键。清洁时间取决于清洁表面的状况。
If you want to stop cleaning during the cleaning of ultrasonic cleaning equipment, you should first adjust the power to very small, and then press the stop key. The cleaning time depends on the condition of the cleaned surface.
超声波清洗器溢出
Ultrasonic washer overflow
如果清洗池的液面上浮油过多,应打开清洗机的溢流装置将其清除,防止对被清洗物造成二次污染。具体操作如下:打开溢流排放阀,将水或清洗液注入清洗池,直到清洗液开始溢出(建议使用刮刀式器具将浮油向溢流口切割,促使其快速流出),保持溢流排放阀常闭,防止意外溢流造成地面污染。
If there is too much oil floating on the liquid level of the cleaning tank, open the overflow device of the cleaning machine to remove it to prevent secondary pollution to the cleaned objects. The specific operations are as follows: open the overflow discharge valve and inject water or cleaning solution into the cleaning tank until the cleaning solution begins to overflow (it is recommended to use a scraper to cut the floating oil to the overflow port to make it flow out quickly), and keep the overflow discharge valve normally closed to prevent accidental overflow from causing ground pollution.
超声波清洗机在如今生活的日常商业与工业及更多的作业中应用颇多,但是由于超声波清洗机也是有许多使用学问的,比如说超声波清洗机在使用安装的过程中就存在这很多的步骤,以上便是相关内容了,您想更详细的了解就来网站www.jnthcsb.com咨询吧。
Ultrasonic cleaning machine is widely used in daily business, industry and more operations in today's life. However, because ultrasonic cleaning machine also has a lot of use knowledge, for example, there are many steps in the process of using and installing ultrasonic cleaning machine. The above is the relevant content. If you want to know more, please come to the website for consultation.