全自动超声波清洗设备在很多行业都有应用，不仅仅是因为它效果好，重要的它大大节省了企业成本。为了更好的应用全自动超声波清洗设备，下面先给大家介绍一下全自动超声波清洗设备。

Full automatic ultrasonic cleaning equipment has been applied in many industries, not only because of its good effect, but also because it greatly saves enterprise costs. In order to better apply the full-automatic ultrasonic cleaning equipment, let's first introduce the full-automatic ultrasonic cleaning equipment.

做好预备工作和喷沙处理

Make preparations and sand blasting

在正式的地进行全自动超声波清洗机的安装前，要把所需胶接的超声波换能器（配好对的）、胶水等应该一一的先准备就绪。同时应该把所需胶接的超声波换能器、缸体进行喷沙处置，喷沙胶接面必须达到要求以及喷沙使用一定要求的金刚沙，对于沙子的要求比较高，比如要精挑细选、保持枯燥等等；且喷沙时紧缩空气的压力应注意调整到规定要求，并经过气源处置器去湿后的高压空气。

Before the formal installation of the full-automatic ultrasonic cleaning machine, the required adhesive ultrasonic transducers (equipped with the right ones), glue, etc. should be prepared one by one. At the same time, the ultrasonic transducer and cylinder body that need to be bonded should be sandblasted. The sandblasting bonding surface must meet the requirements and the diamond sand with certain requirements should be used for sandblasting. The requirements for sand are relatively high, such as careful selection, keeping dry, etc; In addition, the pressure of compressed air during sand blasting should be adjusted to the specified requirements, and the high-pressure air after dehumidification through the air source processor.

应进行相关的清洗工作

Relevant cleaning shall be carried out

要把喷好沙的缸体和全自动超声波清洗机先停止下来做好清洗，后者要用准备好的溶液进行清洗，基本的要去除外表的一些尘垢，再拿丙酮进行下一遍的清洗工作。同时注意超声波清洗机的缸体需要先后进行多遍清洗过程，凉干后再拿专门的溶液各进行一次漂洗，网垫的厚度应该要合乎要求，并且将不锈钢网异样清洗洁净备用。

Stop the sand sprayed cylinder block and the full-automatic ultrasonic cleaning machine first, and the latter should be cleaned with the prepared solution. Basically, remove some dust on the surface, and then take acetone for the next cleaning. At the same time, it should be noted that the cylinder body of the ultrasonic cleaning machine needs to be cleaned several times successively, and then rinse with a special solution after it is dry. The thickness of the mesh pad should meet the requirements, and the stainless steel mesh should be cleaned differently for standby.

做好烘干、预热处理

Do a good job of drying and preheating

要把清洗好的超声波换能器和缸体及网垫放入烘箱进行烘干，烘干温度也要控制在相应的范围内，然后烘干2小时后冷却到某个温度时进行胶接。在一切胶接预备任务做好后，注意要配好胶水（常温）充沛谐和后疾速进行胶接。

Put the cleaned ultrasonic transducer, cylinder block and mesh mat into the oven for drying, and the drying temperature should be controlled within the corresponding range. Then, after drying for 2 hours, when it is cooled to a certain temperature, conduct bonding. After all bonding preparation tasks are completed, pay attention to prepare the glue (normal temperature) and carry out bonding quickly after full harmony.

安装全自动超声波清洗设备的注意事项大体就是这样了，如果您对此有什么疑问的话就来关注我们网站www.jnthcsb.com吧，有关人员为您讲解更多。

The precautions for installing automatic ultrasonic cleaning equipment are generally like this. If you have any questions about this, please follow our website www.jnthcsb.com, and relevant personnel will explain more to you.