为了保证单工位旋转喷淋清洗机在使用中所受到的损害小化并延长机器的使用寿命，这里小编为您介绍了清洁机的清洗保养方法，供您参考。

In order to minimize the damage to the cleaning machine in use and extend the service life of the machine, here we introduce the cleaning and maintenance methods of the cleaning machine for your reference.

1.保持工作场所清洁、干燥和通风。有利于设备的工作环境，长期高效运行。

1. Keep the workplace clean, dry and ventilated. It is conducive to the working environment of the equipment and long-term efficient operation.

2.电气控制箱和设备通风口应远离灰尘、水蒸气和腐蚀性气体，并定期用压缩空气清洁灰尘。

2. The electrical control box and equipment vent shall be far away from dust, water vapor and corrosive gas, and the dust shall be cleaned regularly with compressed air.

3.定期检查单工位旋转喷淋清洗机设备的绝缘性能，定期检查老化的电气元件，检查地线，确保设备接地良好。

3. Regularly check the insulation performance of the equipment, the aging electrical components and the ground wire to ensure that the equipment is well grounded.

4.当清洗液太脏时，应及时处理，定期清洗储罐并清洗罐内污垢，保持罐内和罐外清洁，可提高清洗罐内的耐久性。

4. If the cleaning solution is too dirty, it should be handled in time. The tank should be cleaned regularly and the dirt inside the tank should be cleaned to keep the inside and outside of the tank clean, which can improve the durability of the tank.

5.有过滤装置的设备，应定期更换滤芯。

5. For equipment with filtering device, filter element shall be replaced regularly.

6.确认设备的电源电压满足要求，定期检查电源，避免长时间在不稳定电源下工作。

6. Confirm that the power supply voltage of the equipment meets the requirements, and check the power supply regularly to avoid working under the unstable power supply for a long time.

7.对于有传动机构的，应按要求定期加注润滑油、黄油等润滑油，并定期更换减速机齿轮油，以保证运动部件的平稳运行。

7. For those with transmission mechanism, lubricating oil such as lubricating oil and butter shall be added regularly as required, and gear oil of reducer shall be replaced regularly to ensure smooth operation of moving parts.

8.不要从超声波控制柜顶部的进口处溅出导电液体。否则会严重损坏清洗设备的电路系统。

8. Do not splash conductive liquid from the inlet on the top of the ultrasonic control cabinet. Otherwise, the circuit system of the cleaning equipment will be seriously damaged.

9.避免单工位旋转喷淋清洗机机器剧烈震动或碰撞。

9. Avoid violent vibration or collision of the machine.

10.机器连续运行时间应小于4小时。如果超过这个时间，须将超声波调节旋钮转到“0”位置，让风机继续冷却。

10. The continuous operation time of the machine shall be less than 4 hours. If this time is exceeded, the ultrasonic adjusting knob must be turned to the "0" position to allow the fan to continue cooling.

11.对于长时间运行的清洗机，停机前将电源旋钮调至零，风机工作5分钟后关闭，以确保电源内部的热量被散发。

11. For the washing machine running for a long time, set the power knob to zero before shutdown, and turn off the fan after working for 5 minutes to ensure that the heat inside the power supply is dissipated.

12.定期运行油泵，每次至少10分钟。

12. Run the oil pump regularly for at least 10 minutes each time.

13.用完后，用盖子盖上，防止潮湿和灰尘。

13. After use, cover it with a cover to prevent moisture and dust.

以上内容是清洗机的基本维护方法。无论什么机器，都需要精心维护，以确保使用效率。欲了解更多相关类型的清洗机信息，请关注我们网站www.jnthcsb.com进行咨询吧！

The above contents are the basic maintenance methods of the cleaning machine. No matter what machine, it needs careful maintenance to ensure the efficiency of use. For more information about related types of washers, please visit our website www.jnthcsb.com for consultation!