网带式超声波喷淋清洗机，通过式超声波喷淋清洗烘干线应用广泛，很多人不知道他的工作流程，固特宏业生产的这台网带式超声波喷淋清洗机有效去油，除蜡，除锈，除污。有清洗、漂洗、干燥等功能。

The mesh belt ultrasonic spray cleaning machine is widely used in through type ultrasonic spray cleaning and drying lines, and many people are unaware of its workflow. The mesh belt ultrasonic spray cleaning machine produced by Gute Hongye effectively removes oil, wax, rust, and dirt. It has functions such as cleaning, rinsing, and drying.

网带式超声波喷淋清洗机工艺流程：投料→ 超声波去污（28KHZ）→ 超声波清洗（40K）→ 清水或纯水（鼓泡）→ 风吹→ 下料

Process flow of mesh belt ultrasonic spray cleaning machine: feeding → ultrasonic cleaning (28KHZ) → ultrasonic cleaning (40K) → clear water or pure water (bubbling) → air blowing → discharging

网带式超声波喷淋清洗机由超声波清洗系统、箱体室、罐体加热系统、输送链及传动系统、压缩空气干燥系统、油水分离器、自动刮油机、电气控制系统等组成.

The mesh belt ultrasonic spray cleaning machine consists of an ultrasonic cleaning system, a box chamber, a tank heating system, a conveyor chain and transmission system, a compressed air drying system, an oil-water separator, an automatic oil scraper, an electrical control system, etc

网带式超声波喷淋清洗机为链条网带通超型超声波清洗漂洗机。采用专用链条传动输送工件，具有清洗、漂洗、吹水等功能。将工件手动放置在传动链的网带上，然后通过通超声波清洗室、超声波清洗室、鼓泡清洗室和喷水室。清洗、漂洗、干燥等工序完成后，物料排出。清洗液经净化处理后可循环使用，上罩内的水雾经抽风机抽出后排放至主排气管。该机具有多工位、功能齐全、结构合理、操作方便、清洗效果好等优点，对流水线零件的清洗、改善工作环境、提高清洗干燥质量具有重要意义。

The mesh belt ultrasonic spray cleaning machine is a chain mesh belt through ultrasonic cleaning and rinsing machine. Using a dedicated chain transmission to transport workpieces, it has functions such as cleaning, rinsing, and blowing water. Manually place the workpiece on the mesh belt of the transmission chain, and then pass it through the ultrasonic cleaning room, ultrasonic cleaning room, bubble cleaning room, and spray room. After the cleaning, rinsing, drying and other processes are completed, the materials are discharged. The cleaning solution can be recycled after purification treatment, and the water mist inside the upper cover is extracted by the exhaust fan and discharged to the main exhaust pipe. This machine has the advantages of multiple workstations, complete functions, reasonable structure, easy operation, and good cleaning effect. It is of great significance for cleaning water line parts, improving the working environment, and enhancing the quality of cleaning and drying.

网带采用专用不锈钢网带。由于工件较重，采用三链形式，保证每平方分米轴承压力不低于20kg。工件用专用夹具固定在网带上，保证无滑动、无接触、易清洁.

The mesh belt adopts a dedicated stainless steel mesh belt. Due to the heavy weight of the workpiece, a three chain form is adopted to ensure that the bearing pressure per square decimeter is not less than 20kg. The workpiece is fixed on the mesh belt with a special fixture to ensure no sliding, no contact, and easy cleaning

调速面板配有：转速表、电源开关、指示灯、保险丝、表盘、调速旋钮。使用时应先启动输送电机；然后将速度控制器电源开关置于“on（通）”位置，指示灯亮；轻轻转动调速旋钮，即可改变调速电机的转速：顺时针方向转速升高，逆时针方向转速降低；然后按下转速表以稳定所需的速度。停机时，先将调速控制器电源开关置于“off”位置；2-3分钟后关闭输送电机。

The speed control panel is equipped with a tachometer, power switch, indicator light, fuse, dial, and speed control knob. When using, the conveyor motor should be started first; Then place the power switch of the speed controller in the "on" position, and the indicator light will turn on; Gently rotate the speed control knob to change the speed of the speed control motor: the speed increases clockwise and decreases counterclockwise; Then press the tachometer to stabilize the desired speed. When shutting down, first place the power switch of the speed controller in the "off" position; Turn off the conveyor motor after 2-3 minutes.