欢迎访问济南科尔超声波设备有限公司网站!

专注生产工业用超声波清洗机

让工业清洗无难事

电话

业务咨询电话:

18663767799

你所在位置: 首页-新闻动态-常见问题分享喷淋式清洗机机的日常操作
常见问题

分享喷淋式清洗机机的日常操作

作者:admin来源:http://www.jnthcsb.com/时间:2020-12-28

一:注意事项

1: Precautions

1清洗机应存放并由专门人员进行维护。

1. The cleaning machine should be stored and maintained by special personnel.

2严格操作以防止发生事故。

Strict operation to prevent accidents.

3在手术过程中,工人因某种原因离开,需要停止供电。

During the operation, the worker left for some reason and needed to stop the power supply.

4发生故障时,可以将其关闭并及时进行维护,以使其可以正常启动。

In case of failure, it can be shut down and maintained in time, so that it can start normally.

5严格按顺序打开和关闭本机。

5. Turn on and off the machine in strict order.

二:运营问题

2: Operational issues

1在操作之前,请检查清洁溶液的浓度和比例是否足够以及储罐的液位是否足够。

1 before operation, please check whether the official concentration and proportion of the cleaning solution are enough and whether the liquid level in the tank is enough.

2将清洗液箱和冲洗液箱的电子接触温度计设置为5060度。

2 set the electronic contact thermometers for the washer and rinse tanks to 50 to 60 degrees.

3使用键将电源控制开关置于打开位置。

3 use the key to turn the power control switch to the on position.

4打开加热器以自动开始加热。

4 turn on the heater to start heating automatically.

5打开除油污剂,开始除油。因此,水泵无法打开,水面安静且排油效果佳。

5. Turn on the degreaser and start degreasing. Therefore, the water pump can not be opened, the water surface is quiet and the oil drainage effect is the best.

2-20122Q1434IG.jpg

6温度升预定值后,操作开始,操作员根据需要选择开关,然后按下每个单个操作按钮以执行泵送,抽吸,运输和其他操作。

6 when the temperature rises to a predetermined value, the operation starts, and the operator selects the switch as required, and then presses each single operation button to perform pumping, suction, transportation and other operations.

7机器运行时,操作员可以将零件从装载口连续装载到传送带上,并从清洗,漂洗,吹干,出纸和出纸口中取出已清洗的零件。

When the machine is running, the operator can continuously load the parts from the loading port to the conveyor belt, and take out the cleaned parts from the cleaning, rinsing, drying, paper outlet and paper outlet.

三:关机问题

3: Shutdown problem

1清洁后除去后一部分时,请按停止按钮以停止整个机器。

1 when the last part is removed after cleaning, press the stop button to stop the whole machine.

2应定期向清洁液中添加自来水和一定比例的金属清洁液以补充消耗量,以保持液面在一定高度,如果清洁效果不符合工艺要求,则应更换所有清洁液。

2. Tap water and a certain proportion of metal cleaning solution should be added to the cleaning solution regularly to supplement the consumption, so as to keep the liquid level at a certain height. If the cleaning effect does not meet the process requirements, all cleaning solutions should be replaced.

3清洁设备后,关闭电源。

3. After cleaning the equipment, turn off the power.

四:清洗机日常保养

4: Daily maintenance of cleaning machine

1添加清洁剂或更换清洁溶液,并及时冲洗溶液。

1. Add cleaning agent or replace cleaning solution, and wash the solution in time.

2定期检查自来水的供应量,并根据液位计及时添加全部水。

2 regularly check the supply of tap water, and add all water in time according to the liquid level meter.

3如果需要紧急停止,请按紧急停止按钮停止。

If you need an emergency stop, please press the emergency stop button to stop.

4及时滤网上的灰尘,以保持清洁液箱和冲洗箱的清洁。

4 remove the dust on the filter screen in time to keep the cleaning liquid tank and flushing tank clean.

5润滑零件需要及时加油。

Lubricating parts need to be refueled in time.