全自动超声波清洗机具有不伤工件、清洁范围广、清洗干净彻底、绿色、节省人工等优势，大大提高了清洗工作效率。下面来介绍超声波清洗仪器九点操作注意事项。

The full-automatic ultrasonic cleaning machine has the advantages of no damage to the workpiece, wide cleaning range, thorough cleaning, green environmental protection and labor saving, which greatly improves the cleaning efficiency. Here are the nine points for attention in the operation of ultrasonic cleaning instrument.

1.超声波清洗机应处在干燥、通风、洁净的工作环境中。远离热源，避免放置在潮湿的环境中。

1. the ultrasonic cleaning machine shall be in a dry, ventilated and clean working environment. Keep away from heat sources and avoid placing in a humid environment.

2.定期清理清洗槽、储液槽内的污垢，保持仪器内外洁净。

2. regularly clean the dirt in the cleaning tank and liquid storage tank to keep the inside and outside of the instrument clean.

3.电气控制箱及设备通风口要避免溅入液体，并远离水蒸气、粉尘、腐蚀性气体等，定期清理灰尘。

3. avoid splashing liquid into the electrical control box and equipment vent, keep away from water vapor, dust, corrosive gas, etc., and clean the dust regularly.

4.带有过滤装置的超声波清洗机，要定期更换滤芯。

4. for ultrasonic cleaning machine with filtering device, the filter element shall be replaced regularly.

5.带有传动机构的超声波清洗机，要定期注入润滑油，确保传动机件在良好润滑条件下工作。

5. the ultrasonic cleaning machine with transmission mechanism shall be regularly injected with lubricating oil to ensure that the transmission parts work under good lubrication conditions.

6.对于易老化的电气组件定期进行检查，定期测试设备的绝缘性能。

6. regularly inspect the electrical components that are prone to aging and regularly test the insulation performance of the equipment.

7.仪器连续工作不得超过4个小时，如连续工作时间过长，应旋转超声调节旋钮“0”位，让散热风扇继续工作，以保证电源内部热量散出，让仪器稍做休整后再使用。长时间运行后，关闭仪器前，也应照此操作，让仪器先将内部热量散出再关机。散热一般需要3~5分钟。

7. the continuous operation of the instrument shall not exceed 4 hours. If the continuous operation time is too long, the ultrasonic adjustment knob shall be rotated to "0" position to allow the cooling fan to continue to work, so as to ensure that the internal heat of the power supply is dissipated, and the instrument can be used after a slight rest. After long-time operation, the instrument shall also be operated according to this operation before shutting down, so that the instrument can dissipate the internal heat before shutting down. Heat dissipation generally takes 3-5 minutes.

8.定期让油泵运转一次，每次少在10分钟以上。

8. run the oil pump regularly for at least 10 minutes each time.

9.长时间不用时，用罩子将全自动超声波清洗机罩起来，做好防潮防尘。

9. when it is not used for a long time, cover the full-automatic ultrasonic cleaning machine with a cover to prevent moisture and dust.

以上便是问题的相关解答内容了，如果您想获取更多相关信息，就来关注www.jnthcsb.com我们网站吧！

These are the answers to the questions. If you want to get more information, please follow www.jnthcsb Com our website!