CNC高压清洗机长时间运作时，设备也会出现一些小毛病，当故障出现时，操作员只需根据不一样故障现象，细心查找原因，及时疑问即可。下面咱们首要介绍一些CNC高压清洗机多见的问题以及方法。

When the CNC high-pressure washer operates for a long time, the equipment will also have some small problems. When the fault occurs, the operator only needs to carefully find the cause and solve the problem in time according to different fault phenomena. Here we mainly introduce some common problems and solutions of CNC high-pressure washer.

1、CNC高压清洗机在作业的进程中假如呈现反常的尖叫声，多见原因是因为电机轴承缺油致使的。只要在电机的注油孔写入普通黄油就可以，这种状况出现的不多。咱们在CNC高压清洗机定时修理保护时给予弥补就可以了。

1. If the CNC high-pressure washer shows abnormal squeal during operation, the common reason is that the motor bearing is lack of oil. It can be solved by writing ordinary butter into the oil filling hole of the motor, which rarely occurs. We can make up for it when the CNC high-pressure washer is regularly repaired and protected.

2、CNC高压清洗机在发动后，呈现压力不稳定或时有时无，这里大都原因是高压水泵或进水管路内吸入了空气所致使的，这时需求查看水源的压力是不是满足，进水过滤器是不是阻塞，假如发现滤网阻塞,将滤网取下用水清洗就可以了。

2. After the CNC high-pressure washer is started, the pressure is unstable or sometimes absent. Most of the reasons are caused by the intake of air in the high-pressure water pump or water inlet pipe. At this time, it is necessary to check whether the pressure of the water source is met and whether the water inlet filter is blocked. If the filter screen is found to be blocked, remove the filter screen and clean it with water.

3、CNC高压清洗机在作业的进程中有必定的作业压力可是调不到设备的额外压力或者说压力只停留在必定范围内而不能上升，在这种状况下，要判别高压喷嘴的孔径是不是匹配。

3. The CNC high-pressure washer has a certain operating pressure in the process of operation, but the additional pressure of the equipment cannot be adjusted, or the pressure only stays within a certain range and cannot rise. In this case, it is necessary to judge whether the aperture of the high-pressure nozzle is matched.

如替换高压喷嘴后压力依然上不去，这时需求查看调压阀是不是调到位了，假如在扫除这两种状况下故障照旧，这阐明泵内密封组件损坏或者是活塞损坏，这种状况需求联络厂商帮忙修理。

If the pressure still cannot rise after replacing the high-pressure nozzle, check whether the pressure regulating valve is adjusted to its position. If the fault is still the same under these two conditions, it indicates that the sealing component in the pump is damaged or the piston is damaged. In this case, contact the manufacturer for repair.

4、CNC高压清洗机在正常作业必定时刻后压力下降，这种状况首要要查看高压喷嘴是不是严峻磨损。其次需求分别查看调压阀和水泵内部的密封组件。

4. The pressure of the CNC high-pressure washer drops after a certain time of normal operation. In this case, first check whether the high-pressure nozzle is severely worn. Secondly, check the pressure regulating valve and the sealing components inside the water pump.

5、启动设备后，高压水泵没有水射出，这种疑问需求修理人员查看。大多数原因是进水流量阀不能打开造成的，假如扫除这种状况下疑问照旧，那即是高低压水路串联了。

5. After the equipment is started, no water is ejected from the high-pressure water pump, which needs professional repair personnel to check. Most of the reasons are that the inlet flow valve cannot be opened. If the problem remains the same under this condition, it is that the high and low pressure waterways are connected in series.

此外操作者在使用过程中务必遵循相关的正确的原则，才能使高压清洗机发挥出更好的作用。详情内容了解就来我们网站www.jnthcsb.com咨询吧！

In addition, the operator must follow the relevant correct principles in the use process to make the high-pressure cleaner play a better role. For more information, please visit our website www.jnthcsb.com!