自从碳氢清洗机问世以来，它一直受到精密零部件行业的青睐。一方面，它可以实现高质量的清洁，另一方面，它可以减少污染。毕竟，污染是精密仪器的天敌。碳氢清洗机在使用中有很多优点，但这些优点的成本是操作更麻烦，由于操作错误会出现故障，所以我们应该注意以下注意事项。

Since the hydrocarbon cleaning machine came out, it has been favored by the precision parts industry. On the one hand, it can achieve high-quality cleaning, on the other hand, it can reduce pollution. After all, pollution is the natural enemy of precision instruments. The hydrocarbon washer has many advantages in use, but the cost of these advantages is that it is more troublesome to operate. Because the operation error may cause failure, we should pay attention to the following precautions.

碳氢清洗机在使用时要求非常好，清洗机的进水压力应为0.3～0.5MPa在此范围内，此外，在使用碳氢清洗机时，您还需要定期检查和清洁进水过滤器和过滤器，并确保其过滤器清洁和畅通。这是一个非常重要的一点。如果长时间堵塞，仍然会对设备的运行效果产生很大影响，严重时会损坏设备。因此，定期检查也是一个不容忽视的问题。

The hydrocarbon washer is required to be very good in use, and the water inlet pressure of the washer should be within the range of 0.3~0.5MPa. In addition, when using the hydrocarbon washer, you also need to regularly check and clean the water inlet filter and filter, and ensure that the filter is clean and unblocked. This is a very important point. If it is blocked for a long time, it will still have a great impact on the operating effect of the equipment, and in serious cases, it will damage the equipment. Therefore, regular inspection is also a problem that cannot be ignored.

此外，员工在使用碳氢清洗机时也会定期检查机油。如果他们想更换润滑油，他们应该根据需要更换润滑油。在冬季，他们还应做好防冻工作。松开螺旋泵头和过滤器柱头，排水并倒入防冻液。

In addition, employees also regularly check the oil when using the hydrocarbon washer. If they want to change the lubricant, they should change the lubricant as needed. In winter, they should also do a good job of antifreeze. Loosen screw pump head and filter head, drain water and pour antifreeze.

使用时，建议检查柱塞密封是否泄漏。如果发现泄漏或有更多水滴泄漏，应及时更换柱塞密封。在年底前的工作中，须按下关闭前释放的压力，按下红色压力释放按钮并点亮，然后等待绿灯熄灭。当压力为0时，设备空载运行2~3分钟后关掉电源。

When using, it is recommended to check the plunger seal for leakage. If leakage or more water drops are found, replace the plunger seal in time. During the work before the end of the year, press the pressure released before closing, press the red pressure release button and light it up, and then wait for the green light to go out. When the pressure is 0, turn off the power after the equipment runs for 2-3 minutes without load.

要定期检碳氢清洗设备，避免设备故障影响清洗；注意清洗设备的功率调节，功率过大可能会打伤产品；风干设备调整干燥参数。应使用干净无污染的油抽取清洗剂，取液后及时封盖，避免挥发损耗。更多相关事项就来我们网站www.jnthcsb.com咨询吧！

The hydrocarbon cleaning equipment shall be inspected regularly to avoid equipment failure affecting the cleaning; Pay attention to the power regulation of the cleaning equipment. Excessive power may damage the product; Air drying equipment adjusts drying parameters. Clean and pollution-free oil shall be used to extract the cleaning agent, and the liquid shall be timely covered to avoid volatilization loss. For more information, please visit our website www.jnthcsb.com!